Recent content by rfmicro

  1. R

    stroke recovery

    Les, I had two TIAs, the last being about ten years ago. They scared the everliving c*&p out of me and still do when I think about it. These were minor hiccups compared to what you are going through. With a good rehab and a change in lifestyle, you will surley get through this. Best of luck...
  2. R

    JV models sawmill construction

    Glen, if you search for Keystone Edger you should get some rough pictures of the edger. Having said that, there are some good saw mill sites on the web that will reinforce your layout and should have photos of all the equipment. I would have provided the site in question, but that was on my...
  3. R

    To build a new layout or rebuild the old one?

    Phil, while I do not have that particular book, I would recommend from experience that you start small. This is not meant to demean any inherent skills you may possess, but you can try out a lot of ideas you may read about and make your mistakes on a smaller layout. A larger layout requires a...
  4. R

    Here's two HO Scale photos

    Kyle, two very nice and timely photographs. The first settles my question on the hump yard entrance with perhaps a ladder design for the yard exit. The second photograph was also very timely as I have been looking for a diorama scene for my FSM Baily's Produce rather than mounting it on a flat...
  5. R

    Sawmill

    I have a Coon Gap Saw Mill if you are still looking. Sierra West is sold out, but still taking orders. Just call Brett Gallant. Regards, Trent Mulkern Mechanicsville, MD
  6. R

    30"x48" N setup

    Chad, your use of a projector is a great idea and very practical as well. Regards, Trent
  7. R

    Ballasts with plastic roadbed attached

    Concur above. I have also ballasted EZ Bachman track. The ballast on/near the ties needs to be a very thin layer, perhaps a single layer so you won't bury the track ties. Glue with scenic glue or elmer's/water solution. Regards, Trent
  8. R

    I Need An Estimate

    I estimate the Bachman track and switches, etc at approx $433+ or - depending on where you buy the track. Add on a 1/4" 4' X 8' plywood base, 1" foam 4' X 8' and glue and your looking at somewhere approx $500+. I believe the Bachman track and switches are DCC friendly if you want to go that...
  9. R

    Some Blue Foam Questions

    You may also find the hot wire foam cutter at Woodland Scenics where I got mine. There are probably other vendors that are cheaper. The hot wire foam cutter is probably the best for initial cuts on larger foam. The use of a wire brush also achoeves good results to acieve a smoother form. For...
  10. R

    Need Layout Help

    CNCPGUY, One solution would be to take section Nr. 3 and make two modules. One would be the main and siding (3A), and the second would contain the single track (3B). Section 3B would be a removable section shaped like a trapazoid. You could then pull out (or push in)section 3B, enter your...
  11. R

    EZ Track, yes or no?

    I have to agree with Andrew that there is a place for modular, ballasted track made by vendors such as Kato, Atlas and Bachman to name a few. While more expensive it can ease the design and track laying tasks. It can also be ballasted just like flex track with the end results looking just as...
  12. R

    Strange request needed....shale rock

    Patrick, I would have to agree with Andrew, that your best (and least cost) bet is to fabricate the shale formation that you are looking for with layered ceiling tile or foam and a good wire brush/exacto knife to make the stratified rock formations. That and some effort in rock formation...
  13. R

    Beginner Needs Help

    SLC, any of the track metioned in your post will work. As it comes with plastic balast as part of the track, you can use it as is or add additional ballast later for a more prototypical look. It is easy to work with but costs more than due to the addition of the plastic ballast. You can glue...
  14. R

    Control and sound decoder all in one?

    MRC makes all-in-one decoders. I would not be surprised if all the DCC mfrs sold all-in-one sound and control decoders. Regards, Trent
  15. R

    Help!

    My apologies as I have not read all 5 pages of the thread. For HO I believe the standard separation is 2.5-inches center to center. The NMRA web site should also have that information should you need to double check. Regards, Trent
Top