Star Trek XI Enterprise

Status
Not open for further replies.

sidewinder81777

Midnight Modeler
This is Paragon's new enterprise with a few modifications to the primary hull to look more like the movie. I modified the area around the deflector. Extended the flat bottom further forward, and modified the shuttle bay area a little.

DSCN0109.jpg


DSCN0115.jpg


DSCN0117.jpg


DSCN0111.jpg


DSCN0113.jpg
 

bf109

Member
great job ... again :thumb: were there any problems , wiich you had to solve along the way ?
or other builders have to look out for ?
 

mchale

beach boy
Hi can you list the modifications for me the only thing i can see u refited was bottem ledge of the shuttle bay and the photon torpedo tube lancher
 

sidewinder81777

Midnight Modeler
Hi can you list the modifications for me the only thing i can see u refited was bottem ledge of the shuttle bay and the photon torpedo tube lancher

I also extended the flat bottom of the secondary hull further forward and redesigned the forward part of the secondary hull around the deflector
 

Millenniumfalsehood

Well-Known Member
Looks like the nacelles need to be blown up a bit, say to about 145% their current size. The ship's engines in the movie look much 'fatter' than these. Also, I don't believe the pylons should curve quite that much.

But in any case, that's a great build-up! I think I'll have to give it a whirl.
 

sidewinder81777

Midnight Modeler
Looks like the nacelles need to be blown up a bit, say to about 145% their current size. The ship's engines in the movie look much 'fatter' than these. Also, I don't believe the pylons should curve quite that much.

But in any case, that's a great build-up! I think I'll have to give it a whirl.

Saw the movie the next day and straightened out the nacelle pylons some :D
 

zdalin2003

New Member
Hi, great build!! I've just started also :D, but i've hit a dead end... How did you build the warp nacelles? especially the rear part (the inside of the tube)

Thanx in advance :)
 

sidewinder81777

Midnight Modeler
Hi, great build!! I've just started also :D, but i've hit a dead end... How did you build the warp nacelles? especially the rear part (the inside of the tube)

Thanx in advance :)

Honestly I took the end piece and cut out the blue middle portion and kept paring it down until it fit in the nacelle
 

zdalin2003

New Member
Yup, just today i did the same thing :p
Here's my build :D i'm only one warp nacelle away from completion goldtoth1

And here are some pics:
160520091234
 

Attachments

  • 160520091234.jpg
    160520091234.jpg
    136.5 KB · Views: 30
  • 160520091236.jpg
    160520091236.jpg
    95.7 KB · Views: 20
  • 170520091240.jpg
    170520091240.jpg
    143.8 KB · Views: 22

sidewinder81777

Midnight Modeler
where can i get a stand model that works with the theme of star trek xi for this enterprise model?

well what I did was used the risers from the SF Papercraft enterprise-a on a base of thick cardboard with a picture of the ship laminated on to it and the dedication plaque on the front risers.

DSCN0134.jpg
 

Paragon

Active Member
Ok, I've uploaded my stand, there are links to it with the Kelvin and Enterprise. Its simple, just the STXI arrowhead, with pillars to hold up the model.
 

zdalin2003

New Member
Finished!!! (almost :p)

So i've just (almost) finished paragon's star trek xi enterprise model (thank you paragon :thumb:) and here are some pics:

170520091254.jpg


170520091247.jpg


170520091255.jpg




Now all i need to do is to build it a stand, and add it to the fleet :D
Thanks sidewinder81777 and paragon
 
Status
Not open for further replies.
Top